| Hangar |
Aircraft |
Category |
Date |
Preview |
| edtherenderman | Aero-Werkes AW 11601 - Hannover CL IIIa | Build | 23-Mar-20 10:41 |  | | Views : 412 | | Argus III engine block assembled. I needed to do some filler in the front where the 3D print partially failed. |
| edtherenderman | Aero-Werkes AW 11601 - Hannover CL IIIa | Build | 23-Mar-20 10:40 |  | | Views : 511 | | Been a trying time over the last few weeks. Working from home and social isolation has been challenging. But fortunetly, my family, friends and myself are healthy. I hope all the same for you! I have had some time (more time actually) to do some 3D printing. Here is the 3D print job for an 1/16 scale ARGUS (Opel) III six cylinder engine used in the Hannover CIIIa and serveral other German aircraft during WWI. I modeled this is Blender, then using my print pipeline, was able to print it out in five separate print jobs. Most of these only took 4 - 6 hours to print. Print time is proportial to the number of layers (hight in Z Axis) of the print, not the number of parts. I have found there tends to have more issues with lots of parts on one print, so I tend to keep the numbers smaller and do more prints. It took two weekends and a week of evenings to model the entire engine. However, now that I have it, I can print it in any scale I want down to about 1/24. Any smaller than that and I run into issues with parts being too small and would need to rework the model. |
| Don C | Scratch Built Basler BT-67 | Build | 22-Mar-20 18:44 |  | | Views : 413 | | Waiting to be attached. Alll's quiet up here in the mountains. Hope it's the same for the rest. |
| Don C | Scratch Built Basler BT-67 | Build | 22-Mar-20 18:43 |  | | Views : 513 | | Cleaned up. Nacelles next. |
| BriandKilby | West Wings Spitfire Mk 22/24 | Parked | 21-Mar-20 09:51 |  | | Views : 1530 | | all done! |
| BriandKilby | West Wings Spitfire Mk 22/24 | Parked | 21-Mar-20 09:50 |  | | Views : 1453 | |
|
| Hangar |
Aircraft |
Category |
Date |
Preview |
| edbecky | Guillows Series 800 - B-25 Mitchell | Build | 20-Mar-20 11:25 |  | | Views : 1754 | | Trying to finish B-25 if I can stay away from D7. Some cockpit window painting and cleanup left. A few decals and propellers still to do but moving right along. |
| edbecky | Guillows Fokker D-VII | Build | 20-Mar-20 11:20 |  | | Views : 1158 | | Carved one rib and all stringers out of scrap. Will need to fabricate a few rudder pieces but all easy stuff. All else good to go. |
| Don C | Scratch Built Basler BT-67 | Build | 19-Mar-20 14:18 |  | | Views : 579 | | Yesterday evening. Fin and stripe are now done and the tape came off well. nose nest. |
| Don C | Scratch Built Basler BT-67 | Build | 19-Mar-20 14:15 |  | | Views : 482 | | Untaping error under repair. Not sure of the reason. 2 possibilities: 1, pulled tape at the wromg angle (towards the the red instead of towards the white, 2. I got impatient with the acrylic white paint coverage and put 2 coats of Krylon white on and the latex didn't stick well. After this I sanded the white lightly before painging over it. Those 2 corrections seemed to have helped. |
| Don C | Scratch Built Basler BT-67 | Build | 19-Mar-20 14:08 |  | | Views : 463 | | In the paint shop |
| MrStarkSr | Guillows Series 1000 - SBD3 Dauntless | Parked | 19-Mar-20 12:12 |  | | Views : 515 | | Didn't like the bomb thatcame with it |
|
