Main Menu
User Login
User Name
Password

View By Hangar


View By Aircraft

Top Ten Aircraft :
(numbers in brackets represent number of images online)
Top Six Manufacturers :

Browse Images

Virtual Aerodrome Image Browser ( Small / Large ) Show : All | Parked | Flying | Build | Aerial | Reference
Page (3324 in total) :  <<   89   90   91   92   93  [ 94 ]  95   96   97   98   99   >>  [ < Prev ] [ Next > ]
Hangar Aircraft Category Date Preview
bobgoodScratch Built Percival Q6Parked16-Nov-21 18:09
Views : 858
Still a few little bits of trim/paint to do......
edtherendermanScratch Built Bugatti 100PFlying14-Nov-21 19:49
Views : 419
This is the buck for heat forming the canopy. 3D modeled and printed on FDM printer with Polysmooth.
edtherendermanScratch Built Bugatti 100PBuild14-Nov-21 19:47
Views : 402
3D modeled and printed the spinners and propellers. These are just press fitted at this point and still have some fitting to do, but the results look good. Spinners were done with my FDM printer using Polysmooth filament. The propellers were done with my SLA printer.
edtherendermanScratch Built Bugatti 100PBuild14-Nov-21 19:45
Views : 392
Port side exhaust fairing for back engine and cooling air outlet on trailing edge of wing.
edtherendermanScratch Built Bugatti 100PBuild14-Nov-21 19:44
Views : 388
Bottom View
edtherendermanScratch Built Bugatti 100PBuild14-Nov-21 19:44
Views : 400
Taking a break for the holidays so thought I’d post the current state of the Bugatti. 3D printed exhaust fairing and cooling air outlets that are on the trailing edge of the wings. Glued and filled with spackling, then coated entire model with five coats of thinned EZ-DOPE. Finally, two coats of sanding primer. Next will be sanding the primer and filling anything that needs it.
Hangar Aircraft Category Date Preview
mark eggebeenGuillows Series 2000 - B17 Flying FortressParked12-Nov-21 22:55
Views : 798
Major surgery !! I forgot to install the guides for the nacelle rails on one wing . Now I built the nacelle and am using it to align the guides with the rails
BriandKilbyGuillows 1903 Wright FlyerBuild12-Nov-21 13:24
Views : 529
wondering if staining the propellers would look better than painting or leaving it normal? what do you guys think?
mark eggebeenGuillows Series 2000 - B17 Flying FortressParked11-Nov-21 22:24
Views : 530
Don CScratch Built Vultee BT-13Build10-Nov-21 21:24
Views : 424
This should be 1st . ready to go. Oven heated to 280. Let it heat for about 5 minutes, then move quickly. If it doesn't go all the way down over the mold, back in the oven for a longer time. It will flatten out and give you a second chance..
Don CScratch Built Vultee BT-13Build10-Nov-21 21:18
Views : 436
Its helpful to mark where to cut before removing it from the form. I made 2 in case I messone up fitting or painting.
Don CScratch Built Vultee BT-13Build10-Nov-21 21:15
Views : 457
Cooled . Haad ro work a bit to get it off the form
Page (3324 in total) :  <<   89   90   91   92   93  [ 94 ]  95   96   97   98   99   >>  [ < Prev ] [ Next > ]
(c) 2010 www.VirtualAerodrome.com / James Good. All pictures are property of the individual members of this site.
They may not be used without permission from the user.